Expresiones
Resumen
Es posible definir propiedades utilizando expresiones matemáticas. En la interfaz gráfica de usuario, los cuadros de giro o campos de entrada que están vinculados a las propiedades contienen un icono azul . Haciendo clic en el icono o escribiendo el signo igual = aparece el editor de expresiones para esa propiedad en particular.
Es una expresión matemática que sigue la notación de los operadores y funciones matemáticas estándar, como se describe a continuación. Además, la expresión puede hacer referencia a otras propiedades, y también utilizar condicionales. Los números en una expresión pueden tener una unidad opcional adjunta.
Numbers may use either a comma ,
or a decimal point .
separating whole digits from decimals.
When the decimal marker is used, it must be followed by at least one digit.
Thus, the expressions 1.+2.
and 1,+2,
are invalid, but 1.0 + 2.0
and 1,0 + 2,0
are valid.
Operators and functions are unitaware, and require valid combinations of units, if supplied. For example, 2mm + 4mm
is a valid expression, while 2mm + 4
is not (the reason for this is that an expression like 1in + 4
will most likely be interpreted as 1in + 4in
by humans, but all units are converted to the SI system internally, and the system is not able to guess this). These units are currently recognized.
You can use predefined constants and functions.
Argumentos de la función
Multiple arguments to a function may be separated by either a semicolon ;
or a comma followed by a space ,
. In the latter case, the comma is converted to a semicolon after entry. When a semicolon is used, no trailing space is necessary.
Arguments may include references to cells in a spreadsheet. A cell reference consists of the cell's uppercase row letter followed by its column number, for example A1
. A cell may also be referenced by using the cell's alias instead, for example Spreadsheet.MyPartWidth
.
Referencia de objetos
You can reference an object by its DatosName or by its DatosLabel. In the case of a DatosLabel, it must be enclosed in double <<
and >>
symbols, such as <<Label>>
.
You can reference any numerical property of an object. For example, to reference a Cylinder's height, you may use Cylinder.Height
or <<Long_name_of_cylinder>>.Height
.
To reference list objects, use <<object_label>>.list[list_index]
or object_name.list[list_index]
. If you want for example to reference a constraint in a sketch, use <<MySketch>>.Constraints[16]
. If you are in the same sketch you may omit its name and just use Constraints[16]
.
Note: The index starts with 0, therefore constraint 17 has the index 16.
For more information about referencing objects, see Reference to CAD_data.
Constantes soportadas
The following constants are supported:
Constant  Description 

e  Euler's number 
pi  Pi 
Operadores soportados
The following operators are supported:
Operator  Description 

+  Addition 
  Subtraction 
*  Multiplication 
/  Floating point Division 
%  Remainder 
^  Exponentiation 
Funciones soportadas
Funciones matemáticas generales
The mathematical functions listed below are available.
Trigonometric functions use degree as their default unit. For radian measure, add rad
following the first value in an expression. So e.g. cos(45)
is the same as cos(pi rad / 4)
. Expressions in degrees can use either deg
or °
, e.g. 360deg  atan2(3; 4)
or 360°  atan2(3; 4)
. If an expression is without units and needs to be converted to degrees or radians for compatibility, multiply by 1 deg
, 1 °
or 1 rad
as appropriate, e.g. (360  X) * 1deg
; (360  X) * 1°
; (0.5 + pi / 2) * 1rad
.
These trigonometric functions are supported:
Function  Description  Value range 

acos(x)  Arc cosine  1 <= x <= 1 
asin(x)  Arc sine  1 <= x <= 1 
atan(x)  Arc tangent  all 
atan2(x; y)  Arc tangent of x/y  all, except y = 0 
cos(x)  Cosine  all 
cosh(x)  Hyperbolic cosine  all 
sin(x)  Sine  all 
sinh(x)  Hyperbolic sine  all 
tan(x)  Tangent  all, except x = n*90 with n = uneven integer 
tanh(x)  Hyperbolic tangent  all 
hypot(x; y)  Pythagorean addition (hypotenuse). E.g. hypot(4; 3) = 5.  x and y > 0 
cath(x; y)  Given hypotenuse, and one side, returns other side of triangle. E.g. cath(5; 3) = 4.  x and y > 0, x >= y 
These functions for exponentiation and logarithmization are supported:
Function  Description  Value range 

exp(x)  Exponential function  all 
log(x)  Natural logarithm  x > 0 
log10(x)  Common logarithm  x > 0 
pow(x; y)  Exponentiation  all 
sqrt(x)  Square root  x >= 0 
These functions for rounding, truncation and remainder are supported:
Function  Description  Value range 

abs(x)  Absolute value  all 
ceil(x)  Ceiling function, smallest integer value greater than or equal to x  all 
floor(x)  Floor function, largest integer value less than or equal to x  all 
mod(x; y)  Remainder after dividing x by y  all, except y = 0 
round(x)  Rounding to the nearest integer  all 
trunc(x)  Truncation to the nearest integer in the direction of zero  all 
Funciones estadísticas/agregadas
Aggregate functions take one or more arguments.
Individual arguments to aggregate functions may consist of ranges of cells. A range of cells is expressed as two cell references separated by a colon :
, for example average(B1:B8)
or sum(A1:A4; B1:B4)
.
The cell references may also use cell aliases, for example average(StartTemp:EndTemp)
.
These aggregate functions are supported:
Function  Description  Value range 

average(a; b; c; ...)  Average value of the arguments; same as sum(a; b; c; ...) / count(a; b; c; ...)  all 
count(a; b; c; ...)  Count of the arguments; typically used for cell ranges  all 
max(a; b; c; ...)  Maximum value of the arguments  all 
min(a; b; c; ...)  Minimum value of the arguments  all 
stddev(a; b; c; ...)  Standard deviation of the values of the arguments  all 
sum(a; b; c; ...)  Sum of the values of the arguments; typically used for cell ranges  all 
String manipulation
String identification
Strings are identified in expressions by surrounding them with opening/closing double chevrons (as are labels).
In following example, "TEXT" is recognized as a string : <<TEXT>>
String concatenation
Strings can be concatenated using the '+' sign.
Following example <<MY>> + <<TEXT>>
will be concatenated to "MYTEXT".
String formatting
String formatting is supported using the (old) %style Python way.
All %specifiers as defined in Python documentation.
As an example, supposing you have a default 10mmside cube named 'Box' default FreeCAD naming, following expression <<Cube length : %s>> % Box.Length
will expand to "Cube length : 10.0 mm"
A limitation is that only one %specifier is allowed in string, thus you have to use string concatenation if more than one is needed. With same above situation, expression <<Cube length is %s>> % Box.Length + << and width is %s>> % Box.Width
will expand to "Cube length is 10.0 mm and width is 10.0 mm".
A FreeCAD sample file using string formatting is available in the forum
Create function
The following objects may be created in expressions via the create
function:
 Vector
 Matrix
 Rotation
 Placement
The create
function passes subsequent arguments to the underlying Python constructor when creating the object.
Various mathematical operations such as multiplication, addition, and subtraction are supported via standard mathematical operators (e.g. *
, +
, 
).
Vector
When create
is passed <<vector>>
as the 1st argument, the next 3 arguments are the X, Y, and Z coordinates for the Vector
respectively.
Example:
create(<<vector>>; 2; 1; 2)
Matrix
When create
is passed <<matrix>>
as the 1st argument, the next 16 arguments are the elements for the Matrix
in rowmajor order.
Example:
create(<<matrix>>; 1; 2; 3; 4; 5; 6; 7; 8; 9; 10; 11; 12; 13; 14; 15; 16)
Rotation
When create
is passed <<rotation>>
as the 1st argument, there are two ways to create a Rotation
:
1. Specify an axis vector and a rotation angle.
Example:
create(<<rotation>>; create(<<vector>>; 0; 1; 0); 45)
2. Specify 3 rotations about the X, Y, and Z axes as Euler angles.
Example:
create(<<rotation>>; 30; 30; 30)
Placement
When create
is passed <<placement>>
as the 1st argument, there are five ways to create a Placement
.
These possible combinations are documented in the below table and are based on the Placement API page.
Number of arguments  Description 

2  create(<<placement>>; Placement)

2  create(<<placement>>; Matrix)

3  create(<<placement>>; Base; Rotation)

4  create(<<placement>>; Base; Rotation; Center)

4  create(<<placement>>; Base; Axis; Angle)

The following example shows the syntax for creating a Placement
from a Base
(vector) and a Rotation
:
create(<<placement>>; create(<<vector>>; 2; 1; 2); create(<<rotation>>; create(<<vector>>; 0; 1; 0); 45))
For readability, you can define vectors and rotations in separate cells, and then reference the cells in your expression.
Matrix functions
mscale
Scale a Matrix
with a given Vector
.
mscale(Matrix; Vector)
mscale(Matrix; x; y; z)
minvert
Invert the given Matrix
, Rotation
, or Placement
.
minvert(Matrix)
minvert(Rotation)
minvert(Placement)
Tuple & list
You can create Python tuple
or list
objects via their respective functions.
tuple(2; 1; 2)
list(2; 1; 2)
Expresiones condicionales
Conditional expressions are of the form condition ? resultTrue : resultFalse
. The condition is defined as an expression that evaluates to either 0
(false) or nonzero (true). Note that enclosing the conditional expression in parentheses is currently considered an error.
The following relational operators are defined:
Unit  Description 

==  equal to 
!=  not equal to 
>  greater than 
<  less than 
>=  greater than or equal to 
<=  less than or equal to 
Unidades
Units can be used directly in expressions. The parser connects them to the previous value. So 2mm
or 2 mm
is valid while mm
is invalid because there is no preceding value.
All values must have a unit. Therefore you must in general use a unit for values in spreadsheets.
In some cases it works even without a unit, for example if you have e.g. in spreadsheet cell B1 just the number 1.5
and refer to it for a pad height. This only works because the pad height predefines the unit mm
that is used if no unit is given. It will nevertheless fail if you use for the pad height e.g. Sketch1.Constraints.Width  Spreadsheet.B1
because Sketch1.Constraints.Width
has a unit and Spreadsheet.B1
has not.
Units with exponents can directly be entered. So e.g. mm^3
will be recognized as mm³ and m^3
will be recognized as m³.
If you have a variable whose name is that of a unit you must put the variable between << >>
to prevent it from being recognized as a unit. For example if you have the dimension Sketch.Constraints.A
it would be recognized as the unit ampere. Therefore you must write it in the expression as Sketch.Constraints.<<A>>
.
The following units are recognized by the expression parser:
Amount of substance:
Unit  Description 

mol  Mole 
Angle:
Unit  Description 

°  Degree; alternative to the unit deg 
deg  Degree; alternative to the unit ° 
rad  Radian 
gon  Gradian 
S  Second of arc; alternative to the unit ″ 
″  Second of arc; alternative to the unit S 
M  Minute of arc; alternative to the unit ′ 
′  Minute of arc; alternative to the unit M 
Current:
Unit  Description 

mA  Milliampere 
A  Ampere 
kA  Kiloampere 
MA  Megaampere 
Energy/work:
Unit  Description 

J  Joule 
Ws  Watt second; alternative to the unit Joule 
VAs  Voltamperesecond; alternative to the unit Joule 
CV  Coulombvolt; alternative to the unit Joule 
Force:
Unit  Description 

mN  Millinewton 
N  Newton 
kN  Kilonewton 
MN  Meganewton 
lbf  Pound of force 
Length:
Unit  Description 

nm  Nanometer 
um  Micrometer; alternative to the unit µm 
µm  Micrometer; alternative to the unit um 
mm  Millimeter 
cm  Centimeter 
dm  Decimeter 
m  Meter 
km  Kilometer 
mil  Thousandth of an inch; alternative to the unit thou 
thou  Thousandth of an inch; alternative to the unit mil 
in  Inch; alternative to the unit " 
"  Inch; alternative to the unit in 
ft  Foot; alternative to the unit ' 
'  Foot; alternative to the unit ft 
yd  Yard 
mi  Mile 
Luminous intensity:
Unit  Description 

cd  Candela 
Mass:
Unit  Description 

ug  Microgram; alternative to the unit µg 
µg  Microgram; alternative to the unit ug 
mg  Milligram 
g  Gram 
kg  Kilogram 
t  Tonne 
oz  Ounce 
lb  Pound; alternative to the unit lbm 
lbm  Pound; alternative to the unit lb 
st  Stone 
cwt  Hundredweight 
Power:
Unit  Description 

W  Watt 
VA  Voltampere 
Pressure:
Unit  Description 

Pa  Pascal 
kPa  Kilopascal 
MPa  Megapascal 
GPa  Gigapascal 
uTorr  Microtorr; alternative to the unit µTorr 
µTorr  Microtorr; alternative to the unit uTorr 
mTorr  Millitorr 
Torr  Torr; 1 Torr = 133.32 Pa 
psi  Poundforce per square inch; 1 psi = 6.895 kPa 
ksi  Kilopoundforce per square inch 
Temperature:
Unit  Description 

uK  Microkelvin; alternative to the unit µK 
µK  Microkelvin; alternative to the unit uK 
mK  Millikelvin 
K  Kelvin 
Time:
Unit  Description 

s  Second 
min  Minute 
h  Hour 
Volume:
Unit  Description 

l  Liter 
The following commonly used units are not yet supported:
Unit  Description  Alternative 

°C  Celsius  [°C] + 273.15 K 
°F  Fahrenheit;  ([°F] + 459.67) × 5/9 
u  Atomic mass unit; alternative to the unit Da  1.66053906660e27 kg 
Da  Dalton; alternative to the unit u  1.66053906660e27 kg 
sr  Steradian  not directly 
lm  Lumen  not directly 
lx  Lux  not directly 
px  Pixel  not directly 
Caracteres y nombres no válidos
The expression feature is very powerful but to achieve this power it has some limitations concerning some characters. To overcome this, FreeCAD offers to use labels and reference them instead of the object names. In labels you can use almost all special characters.
In cases where you cannot use a label, such as the name of a sketch's constraints, you must be aware what characters are not allowed.
Etiquetas
For labels there are no invalid characters, however some characters need to be escaped:
Characters  Description 

' , \ , "

Need to be escaped by adding \ in front of them.

For example, the label Sketch\002
must be referenced as <<Sketch\\002>>
.
Nombres
Names of objects like dimensions, sketches, etc. may not have the characters or character sequences listed below, otherwise the name is invalid:
Characters / Character sequences  Description 

+, , *, /, ^, _, <, >, (, ), {, }, [, ], ., ,, =  Characters that are math operators or part of mathematical constructs 
A, kA, mA, MA, C, G, F, uF, µF, J, K, ' , ft , °, and many more!  Characters and character sequences that are units 
#, !, ?, §, $, %, &, :, ;, \, , ~, ∆, ¿, and many more!  Characters used as placeholder or to trigger special operations 
pi, e  Mathematical constants 
´, `, ' , "  Characters used for accents 
space  A space defines the end of a name and can therefore not be used 
For example, the following name is valid: <<Sketch>>.Constraints.T2üßµ@
. While these are invalid names: <<Sketch>>.Constraints.test\result_2
(\r means "carriage return") or <<Sketch>>.Constraints.mol
(mol is a unit).
Since shorter names (especially if they have only one or two characters) can easily result in invalid names, consider using longer names and/or establishing a suitable naming convention.
Cell aliases
For spreadsheet cell aliases only alphanumeric characters and underscores (A
to Z
, a
to z
, 0
to 9
and _
) are allowed.
Referencia a los datos CAD
It is possible to use data from the model itself in an expression. To reference a property useobject.property
. If the property is a compound of fields, the individual fields can be accessed as object.property.field
.
The following table shows some examples:
CAD data  Call in expression  Result 

Parametric Length of a PartWorkbench Cube  Cube.Length

Length with units mm 
Volume of the Cube  Cube.Shape.Volume

Volume in mm³ without units 
Type of the Cubeshape  Cube.Shape.ShapeType

String: Solid 
Label of the Cube  Cube.Label

String: Label 
xcoordinate of center of mass of the Cube  Cube.Shape.CenterOfMass.x

xcoordinate in mm without units 
Value of constraint in a sketch  Constraints.Width

Numeric value of the named constraint Width in the sketch, if the expression is used in the sketch itself.

Value of constraint in a sketch  MySketch.Constraints.Width

Numeric value of the named constraint Width in the sketch, if the expression is used outside of the sketch.

Value of a spreadsheet alias  Spreadsheet.Depth

Value of the alias Depth in the spreadsheet Spreadsheet

Value of a local property  Length

Value of the DatosLength property in e.g a Pad object, if the expression is used in e.g DatosLength2 in the same object. 
Variables globales de todo el documento
There is no concept of global variables in FreeCAD at the moment. Instead, arbitrary variables can be defined as cells in a spreadsheet using the Spreadsheet workbench, and then be given a name using the alias property for the cell (rightclick on cell). Then they can be accessed from any expression just as any other object property.
Enlace entre documentos
It is possible (with limitations) to define a Property of an object in your current document (".FCstd" file) by using an Expression to reference a Property of an object contained in a different document (".FCstd" file). For example, a cell in a spreadsheet or the DatosLength of a Part Cube, etc. in one document can be defined by an Expression that references the X Placement value or another Property of an object contained in a different document.
A document's name is used to reference it from other documents. When saving a document the first time, you choose a file name; this is usually different from the initial default "Unnamed1" (or its translated equivalent). To prevent links being lost when the master document is renamed upon saving, it is recommended that you first create the master document, create a spreadsheet inside it, and save it. Subsequently, you can still make changes to the file and its spreadsheet but you should not rename it.
Once the master document with the spreadsheet is created and saved (named), it is safe to create dependent documents. For example, assuming you name the master document master
, the spreadsheet modelConstants
, and give a cell an aliasname Length
, you can then access the value as:
master#modelConstants.Length
Note: that the master document must be loaded for the values in the master to be available to the dependent document.
Unfortunately, the integrated checker sometimes claims that a valid name doesn't exist. Continue typing anyway. When you have completed the full reference, the OK button will become active.
Of course, it's up to you to load the corresponding documents later when you want to change anything.
Problemas conocidos / tareas pendientes
 The dependency graph is based on the relationship between document objects, not properties. This means that you cannot provide data to an object and query that same object for results. For example, even though there are no cyclic dependencies when the properties themselves are considered, you may not have an object which gets its dimensions from a spreadsheet and then display the volume of that object in the same spreadsheet. As a workaround use multiple spreadsheets, one to drive your model and the other for reporting.
 The expression parser does not handle parentheses well, and is unable to properly parse some expressions. For example:
= (A1 > A2) ? 1 : 0
results in an error, while= A1 > A2 ? 1 : 0
is accepted. The expression= 5 + ((A1>A2) ? 1 : 0)
cannot be entered in any form.  As stated above, unfortunately, the integrated checker sometimes claims that a valid name doesn't exist. Continue typing anyway. When you have completed the full reference, the OK button will become active.
 FreeCAD does not yet have a builtin expression manager where all expressions in a document are listed, and can be created, deleted, queried, etc. But an addon is available: fcxref expression manager.
 Open bugs/tickets for Expressions can be found in the FreeCAD Bugtracker Expressions category
 FreeCAD scripting: Python, Introduction to Python, Python scripting tutorial, FreeCAD Scripting Basics
 Modules: Builtin modules, Units, Quantity
 Workbenches: Workbench creation, Gui Commands, Commands, Installing more workbenches
 Meshes and Parts: Mesh Scripting, Topological data scripting, Mesh to Part, PythonOCC
 Parametric objects: Scripted objects, Viewproviders (Custom icon in tree view)
 Scenegraph: Coin (Inventor) scenegraph, Pivy
 Graphical interface: Interface creation, Interface creation completely in Python (1, 2, 3, 4, 5), PySide, PySide examples beginner, intermediate, advanced
 Macros: Macros, How to install macros
 Embedding: Embedding FreeCAD, Embedding FreeCADGui
 Other: Expressions, Code snippets, Line drawing function, FreeCAD vector math library (deprecated)
 Hubs: User hub, Power users hub, Developer hub